What are the precautions for the trend and shape of printed conductors on PCB pads?
Views : 887
Update time : 2020-06-09 15:34:10
The SMT reflow soldering process requires that the pads of the two chip components should be independent pads. When the pad is connected to a large-area ground wire, the cross-laying method and the 45°-laying method should be preferred; the wire drawn from the large-area ground wire or the power line should be longer than 0.5mm and wider than 0.4mm; The wire connected to the pad should be led out from the center of the long side of the pad to avoid a certain angle.
The trend and shape of the printed conductor
(1) The printed conductors of the circuit board in SMT should be very short. So if you can walk the shortest, don’t go complicated. Follow what can be easy not to be complicated, to be short but not long. It is very helpful for the quality control of the PCB circuit board in the later period.
(2) The direction of the printed conductor shall not have sharp bends and acute angles, and the angle of the printed conductor shall not be less than 90°. This is because it is difficult to corrode small inner corners when making the board. At the outer corner that is too sharp, the copper foil is easily peeled off or warped. The best form of turning is a gentle transition, that is, the inside and outside corners are the best radians.
(3) When the electric wire passes between the two gaskets without communicating with them, the maximum and equal distance should be kept with them; similarly, the distance between the wires should be uniform and equal and kept the maximum.
(4) When connecting wires between PCB pads, when the center distance between the pads is less than the outer diameter D of the pad, the width of the wire can be the same as the diameter of the pad; when the center distance between the pads is greater than D, the width of the wire should be reduced. When there are more than 3 pads on the pad, the distance between the wires should be greater than 2D.
(5) Copper foil should be reserved for ordinary ground wire as much as possible.
(6) In order to increase the peel strength of the liner, a production line with no conductive effect can be provided.
The trend and shape of the printed conductor
(1) The printed conductors of the circuit board in SMT should be very short. So if you can walk the shortest, don’t go complicated. Follow what can be easy not to be complicated, to be short but not long. It is very helpful for the quality control of the PCB circuit board in the later period.
(2) The direction of the printed conductor shall not have sharp bends and acute angles, and the angle of the printed conductor shall not be less than 90°. This is because it is difficult to corrode small inner corners when making the board. At the outer corner that is too sharp, the copper foil is easily peeled off or warped. The best form of turning is a gentle transition, that is, the inside and outside corners are the best radians.
(3) When the electric wire passes between the two gaskets without communicating with them, the maximum and equal distance should be kept with them; similarly, the distance between the wires should be uniform and equal and kept the maximum.
(4) When connecting wires between PCB pads, when the center distance between the pads is less than the outer diameter D of the pad, the width of the wire can be the same as the diameter of the pad; when the center distance between the pads is greater than D, the width of the wire should be reduced. When there are more than 3 pads on the pad, the distance between the wires should be greater than 2D.
(5) Copper foil should be reserved for ordinary ground wire as much as possible.
(6) In order to increase the peel strength of the liner, a production line with no conductive effect can be provided.
Related News
The function of washing machine control board
Jan .30.2024
The function and sensitivity of the washing machine are mainly determined by the control board
Do you know what we need to pay attention for the production of oven control panels？
Jan .30.2024
There are several key points in the production of oven control panels that cannot be ignored
How to Choose and Buy an Oven Control Board？
Jan .15.2024
Have you ever had the frustration of an oven that won't work properly? If so, it's likely that the oven's control board has malfunctioned.
Should I Repair or Replace My Oven?
Jan .05.2024
In the culinary symphony of a modern kitchen, the oven plays a pivotal role. When this essential appliance falters, it poses a quintessential dilemma: should one opt for repair or replace it altogether? This article delves into various aspects to consider, helping you navigate this conundrum.
